Skip to content
Control arms, bushes and ball joints

Porsche Control Arm Replacement in Dubai

A clunk over speed bumps, a car that wanders on the motorway or a front tyre wearing on its inner edge. We inspect the relevant arms, bushes and ball joints first, tell you which corner and which part is worn, and quote the bush, the joint or the complete arm only when the evidence shows it is needed.

  • Measured firstNo arm is replaced on a noise alone
  • Per cornerFront, rear, left and right named
  • Aligned afterGeometry checked once parts are in
Technician checking a Porsche front control arm ball joint for play on a workshop lift in Dubai
Ball joint play check
Price scope

Quoted per arm, per corner and per axle

Budget for the exact component and quantity, not a whole corner by default. These planning ranges include routine fitting and a 5% VAT allowance. Alignment is separate unless expressly included in your written total.

One arm at one corner
AED 1,500 to 4,500

One compatible complete arm with the bushes and joints supplied in that assembly, routine fitting and basic checks. Other arms and alignment are separate.

Four wheel alignment
AED 300 to 600

Measurement and adjustment where the adjusters are serviceable. Added once after any arm, bush or joint work.

Axle pair
AED 3,000 to 9,000

Calculated planning range for two arms using the per-arm guide, not a separate package offer. One alignment adds AED 300 to 600. Multiple links or revision-matching requirements can change the quantity.

Bush or ball joint only
Quoted after inspection

Depends on whether the part is sold separately for your arm and on pressing time, so it is priced once the arm is identified.

Planning estimates carried over from our suspension repair guide, including its 5% VAT allowance. These are not fixed offers or completed-job prices. Model, front or rear position, upper or lower arm, parts grade and access affect the written quote. Confirm required bolts and nuts, pressing labour, seized adjusters and any calibration separately. No repair begins without your approval.

What a control arm is

Five parts decide how a corner behaves

A control arm links the wheel carrier to the body. It lets the wheel move up and down while holding it at the right angle. Each arm meets the body through rubber or hydraulic bushes and meets the wheel carrier through a ball joint or a bush. Wear in any of these joints lets the wheel shift under load, which is what you feel and hear.

  1. 1
    Upper armLocates the upper part of the wheel carrier where this design is fitted. Layout varies by model and generation.
  2. 2
    Lower armLocates the lower part of the wheel carrier. Bush type and joint arrangement depend on the fitted suspension.
  3. 3
    Ball jointThe pivot at the wheel end. On many Porsche arms it is pressed in and not sold separately.
  4. 4
    Body bushesRubber or fluid filled mounts that absorb shocks where the arm meets the body.
  5. 5
    Toe and camber linksShorter rear arms on the 911 and other models that set the wheel angles.
A clunk is not always the arm

Symptoms and the parts that cause them

Front end noises can come from control arms, strut mounts, anti roll bar links, steering joints or wheel bearings. Inspection must locate the source before a part is ordered. A noise or tyre wear pattern alone does not identify a failed arm.

Clunk over bumps or speed humps

Arm bushBall jointStrut mountAnti roll bar link

Wander or vague steering at speed

Lower arm bushTie rod endWheel bearingAlignment

Inner or outer tyre edge wearing fast

Upper arm playCamber settingToe settingRide height

Shimmy or tug when braking

Lower arm bushBrake discsCaliperWheel bearing

Creak when turning at parking speed

Dry ball jointStrut top bearingBush rubber

Torn rubber boot on a ball joint

Ball jointDirt and water entryGrease loss
Measure before replacing

How play is found and recorded

The inspection uses the support position and loading specified for the fitted suspension. Rubber and hydraulic bushes are designed to flex. Abnormal free play, rubber separation, confirmed fluid loss or damage must be distinguished from normal movement. Findings identify the corner, component and test method, with measured values where the manufacturer specifies a measurable limit.

  1. AWheel rock top and bottomObserve the joint and bearing directly to locate the source of movement.
  2. BWheel rock side to sideCheck steering joints and other possible sources while observing the movement.
  3. CLever at each bushUse the specified load direction and assess abnormal movement or separation, not normal bush flexibility.
  4. DRubber and bootsCracks, splits, torn boots and fluid on the bush are noted and photographed.
  5. ERoad testA road test is considered only after the vehicle is assessed as safe to drive.
Technician using a lever to check a Porsche lower control arm bush for movement under the car
Bush movement check
Inspection decision table

What each finding leads to

The action depends on what was measured or seen, not on the age of the car. Monitoring is appropriate only where the component remains serviceable under the applicable inspection criteria.

Finding How it is known Usual action Alignment
Rubber shows fine surface cracks only Surface checked against model-specific criteria, no abnormal play or separation Monitor Not needed
Abnormal play or separation in a body bush Confirmed using the applicable support position and test method Bush only where the bush is sold and pressed separately Needed
Fluid on a hydraulic bush Seen, then cleaned and rechecked Clean and recheck, confirm the fluid source and assess leakage or abnormal play against the applicable criteria Only if replaced
Abnormal ball joint play or damaged boot Joint observed directly, boot and contamination assessed Ball joint or boot repair only where permitted and serviceable, otherwise the complete arm Needed
Bent arm after an impact Seen and compared with the other side Complete arm, never straightened Needed
Both sides fail inspection or a matched revision is required Inspect both sides and check part revisions Axle pair Needed
Play found at the tie rod, not the arm Movement located at the steering joint Route to steering Needed after tie rod work
Bush types

Rubber, hydraulic or harder upgrades

The bush inside an arm decides how much road noise and shock reaches the cabin. Knowing which type your car uses explains why some parts are pressed in on their own and others come with the arm.

Rubber bush

The most common type. Rubber bonded around a metal sleeve. It ages, cracks and softens with heat and mileage.

Often replaceable on its own

Hydraulic bush

A fluid filled bush designed to damp vibration. Some movement is normal. Identify the fitted bush and the source of any wetness before treating it as a failed hydraulic mount.

Clean and recheck before replacing

Polyurethane upgrade

A harder bush that sharpens steering response. It passes more noise and vibration into the car, which some owners do not want on a daily car.

Optional, discussed first

Spherical bearing

A spherical joint used in some performance applications. It can transmit more noise and vibration than a compliant rubber bush. Suitability depends on the part and intended use.

Track use, on request only

Bush only or complete arm

What can be renewed separately on your Porsche

Whether a bush or ball joint can be replaced on its own depends on the arm design. Separate availability does not by itself establish an approved repair method. Your exact arms are confirmed by chassis number before we quote.

Cracked rubber bush on a Porsche control arm removed from the car
Cracked control arm bush
01

Identify the exact arm

Confirm the VIN, generation, front or rear axle, left or right side and upper, lower or longitudinal arm. A corner can contain several links with different part numbers.

02

Check the bush repair route

A separate bush needs the correct application, permitted pressing procedure and installation orientation. Keep the arm only if its structure, mounting bore and remaining joints are serviceable.

03

Assess the joint and boot

Check abnormal free play, stiffness, boot damage and contamination. A separate joint or boot is an option only where the applicable repair procedure permits it. Otherwise quote the complete arm.

04

Check matching part revisions

Porsche bulletin 44/17 identifies matched replacement requirements for specified axle components on affected 981, 982 and 991 vehicles. Check existing part numbers and current workshop instructions before deciding the quantity.

One side or the pair

When both sides of an axle are replaced

Pairs are not automatic. Both sides are inspected and part compatibility is checked. Some Porsche part revisions require matched replacements even when the opposite side is not worn.

One side worn, other side sound

A single replacement may be appropriate when the opposite side is serviceable and current Porsche parts instructions permit the combination.

Single arm or bush

Both sides worn

Both are replaced together, so the car handles the same left and right and one alignment covers both.

Axle pair

One worn, one starting to wear

The findings and any matching-part requirement are explained first. Deferring a serviceable side is an option only when the fitted combination is permitted.

Your choice

Parts grades

Five ways to source the part

Each grade is named on the quote so you can compare like with like. No single grade is right for every car or budget.

Genuine Porsche

Supplied in Porsche packaging. Selected by the correct Porsche part number and revision.

Specification checked

Original supplier

A part sold under a supplier brand. Supplier status alone does not prove it is identical to the Porsche-boxed part. Confirm the brand, part number and application.

Specification checked

Quality aftermarket

From a known brand. Fit and rubber quality vary, so we only quote brands we trust for your model.

Varies by brand

Rebuilt arm

Your arm cleaned with new bushes pressed in, where the ball joint is sound or serviceable.

Depends on bushes chosen

Upgrade bushes

Polyurethane or spherical bearings. Sharper feel with more noise and vibration in the cabin.

Firmer and louder

New and old Porsche front control arms laid side by side on a workshop bench for comparison
Old and new arms compared
Worn component evidence

What your inspection record shows

Before you approve anything, you receive the findings for each corner with photos of the worn part. The card on the right is an example layout with sample entries, not a record from a customer car.

  • Corner, arm and part named for every finding
  • Test position, abnormal finding and applicable acceptance criterion
  • Photo of the bush, joint or boot concerned
  • Recommended action and the grade options
  • Parts that were checked and found sound
Example layout onlySample entries
CornerPartFindingAction
Front leftLower arm bushRubber separated from sleeveReplace
Front leftBall jointNo play, boot intactSound
Front rightLower arm bushSurface cracks onlyMonitor
Front rightStrut mountNo knock feltSound
Rear bothToe linksNo playSound
Alignment needed after work, yes
Porsche on an alignment platform after control arm replacement with targets fitted to each wheel
Alignment after fitting
Alignment after the job

Why geometry is reset after arm work

Check four wheel geometry after arm or bush work using the applicable Porsche procedure. Record camber, caster and toe where measurable, and adjust only the settings provided for that suspension. An out-of-range non-adjustable angle needs investigation rather than a promise that every angle can be set.

  1. 1Applicable bonded rubber pivot fasteners receive final tightening at the specified normal position. Follow Porsche torque, angle and single-use fastener requirements.
  2. 2Four wheel measurement and adjustment on our alignment page process.
  3. 3Road test after static checks confirm the car is safe, then review the original symptom.

See how alignment and balancing work

At collection

What you take away

01Old partsShown or bagged on request so you can see the wear.
02Corner recordFindings for every arm, including parts left in place.
03Alignment readingsBefore and after values from the alignment check.
04Invoice detailPart numbers, grade, labour and VAT on separate lines.
For a faster answer

Start with your model and symptom

  1. Model and year are enough to start
  2. Which corner the noise seems to come from
  3. When it happens, bumps, braking or turning
  4. Tyre photos if available, taken while safely parked
  5. Recent work if known. Share the VIN privately when needed for parts matching
Questions

Porsche control arm questions

Call or send your model and symptom to arrange an assessment. Photos can help plan checks but cannot confirm joint condition remotely.

Call 056 464 6081 Ask on WhatsApp

How do I know the control arm is the problem?

You cannot be sure from the noise alone. Strut mounts, anti roll bar links, tie rods and wheel bearings make similar sounds. The arm is only blamed when play is measured at its bush or ball joint, or when the arm is visibly bent.

Can you replace just the bush instead of the whole arm?

Often yes, when the bush is sold separately for your arm and the arm and ball joint are sound. On some Porsche arms the joint or bush is not serviceable, and then the complete arm is the correct repair.

Do both sides have to be replaced together?

Not automatically. A single arm can be replaced if the other side is serviceable and the part combination is permitted. Porsche revision-matching requirements can require additional replacements on affected vehicles. Check the VIN, existing part numbers and current instructions before approving the quantity.

Is an alignment needed after control arm work?

A geometry check is part of the repair plan after arm or bush work. Adjustments follow the fitted suspension and Porsche procedure. Alignment is a separate charge unless expressly included in the quoted total.

How much does a Porsche control arm cost in Dubai?

Our budget guide for one new arm at one corner, fitted with basic checks, is AED 1,500 to 4,500, with four wheel alignment at AED 300 to 600. The exact figure depends on model, arm position and parts grade and is confirmed in writing.

My hydraulic bush looks wet. Is it leaking?

Not always. Wetness can come from another component or assembly residue. Identify the bush type, clean the area where appropriate and trace the source. Confirm actual leakage and abnormal condition against the applicable procedure before recommending replacement.

Can a bent control arm be straightened?

No. An arm bent by a kerb or pothole impact is replaced, and the other suspension parts on that corner are checked for damage at the same time.

Are polyurethane bushes a good idea?

They sharpen steering feel but pass more noise and vibration into the cabin. For a daily car, compare comfort, maintenance and compatibility with the original specification. We discuss the trade off before quoting either.

How long does control arm replacement take?

It depends on the arm, the corner and whether parts are in stock. We give the expected time with the quote once the parts are confirmed.

Will worn arms affect my tyres?

Yes. Play in an upper arm or a soft lower bush lets the wheel change angle under load, which often shows as fast wear on one edge of the tyre. Repair and alignment address the confirmed cause, but existing tyre damage cannot be reversed. Tyre pressure, other worn parts and geometry also need checking.

Is it safe to drive with a worn control arm?

Driving suitability cannot be confirmed from a description or photo. If steering is unstable, a wheel is displaced, a joint is loose or an arm is damaged after impact, stop safely and arrange assessment or recovery. Do not road test a suspected unsafe suspension. Less obvious wear still needs inspection before driving advice is given.

Do you use genuine parts?

Genuine Porsche parts can be quoted by application. Ask which supplier-branded or aftermarket alternatives are available for your VIN. The quote should identify the brand, part number, revision, lead time and warranty rather than assume every option is in stock.

What if the noise is still there after the repair?

The road test after fitting covers the same conditions that made the noise. If another worn part shows up, we tell you what was found and quote it separately before any further work.

Is there a warranty on control arm work?

There is no single warranty duration stated here for every arm and parts grade. Request the applicable parts and workmanship terms in writing before approval, including time or mileage limits, exclusions, claim handling and whether removal, refitting and alignment are covered. Confirm those terms on the invoice.

Porsche control arm inspection in Dubai

Find the worn joint before you buy a new arm

We explain the inspection findings and quote the required bush, joint or arm by corner and part number. Alignment is priced separately and the full total is agreed before work.

  • Measured play
  • Per corner quote
  • Alignment after
Call WhatsApp
Scroll to Top